Quadro Quadro4x User's Guide download pdf (Page 36)

Quadro Manual III: Extension User's Guide Extension User’s Menus

Quadro2x, 2xi, Quadro4x, 4xi, Quadro16x, 16xi; (SW Version 5.2.x) 36

selecting Save will display the error “Caller address already exists”. A wildcard is allowed in this field (see chapter Entering SIP Addresses

Correctly

). Entering “*” as PBX or PSTN addresses will apply configuration of Caller ID Based services to all extensions or PSTN users.

The extension number should be inserted into the Forward To text field for the PBX call type. The PSTN number length depends on the area code

and phone number.

Send Notification Via SMS checkbox enables SMS notifications sending to the user’s mobile phone when Unregistered/Inaccessible call forwarding

on the corresponding extension from the certain caller takes place. This checkbox selection enables the Mobile Number text field where the user’s

mobile phone number should be defined. If you feel this service is not working, contact your system administrator to configure the SMS Settings.

Send E-mail checkbox enables email notifications sending to the user’s mailbox when Unregistered/Inaccessible call forwarding on the

corresponding extension from the certain caller takes place. This checkbox selection enables the E-mail Address text field where the user’s email

address should be defined. If you feel this service is not working, contact your system administrator to configure the Mail Settings.

When saving this call forwarding configuration, a message will notify the user that Many Extensions Ringing and Call Hunting services have been

disabled.

Find Me / Follow Me

The Find Me / Follow Me service of the Quadro allows you to configure simultaneously or subsequently ringing destinations on the incoming call

from the certain caller. The ringing destinations can be local PBX extensions, remote SIP or PSTN destinations. From this page you may also adjust

a sequence in which the destinations will ring.

Attention: This service has higher priority over all Caller ID based supplementary services, except for incoming and outgoing call blocking. This

means that if the same caller is configured both in incoming or outgoing call blocking page and Find Me/Follow Me page, the blocking service will

take effect. Besides this, if you have Find Me/Follow Me service enabled along with the Many Extensions Ringing, Forwarding or Call Hunting, only

Find Me/Follow Me service will take effect.

The Enable Service checkbox selection activates the Find Me/Follow Me service on the current extension.

The table displayed here lists destinations where the incoming call from a particular caller will be ringing in the configured sequence.

The Enable/Disable functional buttons are used to enable or

disable ringing on the destinations in the Find Me/Follow Me

table.

The Ring Extension Phone drop down list is used to select

the interval in which the current extension (on which you are

currently configuring the Find Me/Follow Me service) will ring

on the incoming call from the selected caller. With the

Immediately selection, the current extension will ring

immediately as the call comes in.

The Confirmation Passcode text field requires the password

to accept the call for destinations where passcode activation is

enabled (see below). Only digit values are allowed in this text

field.

Fig. III-34 Find Me/Follow Me page

Add opens the Add Entry page to add a destination to the

Find Me/Follow Me table. It consists of the following

components:

Call Type lists the available call types:

• PBX - destination is a local Quadro extensions or Auto

Attendant

• SIP –destination is reached through a SIP server

• PSTN –destination is a PSTN user

• Auto – used for undefined call types. In this case,

routing pattern will be considered here and parsed

through Local Routing Table.

Fig. III-35 Find Me/Follow Me – Add Entry page

The Address text field requires the SIP address (see chapter Entering SIP Addresses Correctly

), extension or PSTN number, where the incoming

call from the certain caller will be ringing. If the address already exists in the table, selecting Save will display the error “Caller address already

exists”. A wildcard is allowed in this field (see chapter Entering SIP Addresses Correctly

). The extension number should be inserted into the Address

text field for the PBX call type. The PSTN number length depends on the area code and phone number.

The Start Ringing drop down list is used to select the interval when the destination will ring after the call from the selected caller comes in to the

current extension. Immediately selection indicates that the destination will ring immediately as the call comes in.

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 42 43 44

Comments to this Manuals

No comments

Quadro Quadro4x User's Guide Page 36

Comments to this Manuals

Related products and manuals for Premise Branch Exchange (PBX) systems Quadro Quadro4x