Quadro Quadro16xi Installation Guide Page 35
- Page / 150
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Quadro Manual II: Administrator's Guide Administrator’s Menus
Quadro2x, 2xi, Quadro4x, 4xi, Quadro16x, 16xi; (SW Version 5.2.x) 34
Add functional button is used to add a new traphost to the table
and opens Add SNMP Traphost page where the new traphost
might be defined. Page consists of the following components:
Traphost text field requires an IP address or the host name of
the traphost. Administrating application’s host address should be
inserted here.
Community text field requires community description (public,
private, etc.) for the administrating application to accept the
notifications about the certain events on the Quadro. Field may
contain some kind of password which should be the same both
on Quadro and on the administrating application for successful
SNMP management.
A group of radio buttons is used to select the SNMP protocol
version used for events notifications delivered by the Quadro to
the administrating application.
Fig. II-58:Add SNMP Traphost page
Diagnostics
The System Diagnostic page gives a possibility of running Network and WAN protocol diagnostics to verify Quadro's connectivity and to download
all system logs for possible problems recovery.
The Start Detecting WAN Protocol button is used to initiate WAN diagnostics that will detect the WAN IP configurations: static or through DHCP
and PPP servers. For static WAN IP configuration, gateway availability is checked. When acting as a client, DHCP and PPP servers' accessibilities
are being verified.
The Start Network Diagnostics button is used to initiate network
diagnostics, i.e., to check the WAN link and IP configuration, to
verify gateway, DNS primary and secondary (if configured) servers'
accessibilities.
The Download system logs button is used to download all logs to
the local PC as a *.tar archive file. These logs can then be used by
the Epygi Technical Support Office to determine the problem that
has occurred on your Quadro.
The Reboot this Device button is used to reboot the Quadro.
Please note that the session with the Quadro will be closed, i.e.,
the Quadro GUI should be newly opened and a new login will be
required afterwards.
For Quadro 2x/4x/16x models, the Start FXO Diagnostics button
runs FXO diagnostic tests to determine the optimal value for the
FXO country specific regional setting (CSRS) appropriate to your
PSTN provider. Once the FXO diagnostic is complete, the
recommended value should be set manually on the fxocfg hidden
cgi. Setting this value may resolve echo or poor audio quality
issues on FXO lines.
Fig. II-59: System Diagnostic page
For Quadro 2xi/4xi/16xi models, the Start ISDN Diagnostics button is used to initiate ISDN BRI low level diagnostic. With these tests the ISDN
physical link is checked and the Frame Synchronization is verified.
The Start USB Flash Memory Testing button is used to test the USB flash memory attached to the Quadro. The system will check whether the
attached USB flash memory is supported by the Quadro or not as well as will perform the elementary procedures (like mounting and data formatting)
on the USB flash memory.
If you use a USB flash memory not supported by the Quadro, the system will inform you about that and you may still continue using that USB flash
memory at your own risk. The list of USB flash memories supported and tested with the Quadro is posted on the Epygi’s Web download portal.
Attention: During the USB flash memory testing, all the data stored on it will be deleted.
The field below will display the diagnostics results and the connectivity conditions. The system should be reconfigured if problems occur during the
diagnostics.
Show System Logs link leads to the page where Quadro’s logs might be viewed, downloaded and the logging setting may be adjusted.
System Logs
The System Logs page is accessible by pressing the Show System Logs link on the Diagnostics page. This page is used to adjust where system
logging settings, view system logs directly in your browser or download them locally to your PC.
The System Logs page consists of three sub-pages.
The System Logs Settings page is used to adjust the system logging settings and contains the following components.
The Enable User Logging checkbox is used to enable user level logging. This logging contains brief information about events on the Quadro.
The Enable Developer Logging checkbox is used to enable developer high level logging. This logging contains detailed information about events
on the Quadro.
- Edition 1, June 2011 1
- Table of Contents 2
- Quadro’s Graphical Interface 6
- Recurrent Buttons 7
- Recurrent Functional Buttons 7
- Administrator’s Menus 8
- System Security Management 12
- • User Rights Management 13
- • IP Line Settings 13
- • Firewall/NAT 13
- Network Status 15
- Memory Status 19
- Hardware Status 20
- SIP Registration Status 20
- IP Lines Registration Status 20
- License Status 21
- IP Routing Configuration 21
- Configuration Management 23
- Time/Date Settings 28
- Mail Settings 29
- SMS Settings 30
- Firmware Update 30
- Automatic Firmware Update 32
- Networking Tools 33
- SNMP Settings 34
- Diagnostics 35
- System Logs 35
- Fig. II-64: Features page 37
- Upload Language Pack 38
- User Rights Management 39
- Users Menu 41
- Extensions Management 41
- User Extension Settings 43
- Call Park Extension Settings 49
- Attendant Extension Settings 55
- • PSTN – calls to PSTN 56
- • User Input 58
- • No input 58
- • Signs (“*” and “#”) 58
- Add Multiple Extensions 61
- Extension Codecs 62
- Call Park Service 63
- Recording Box 64
- Receptionist Management 65
- * key combination (see 67
- Authorized Phones Database 69
- Call Back Services 70
- Telephony Menu 72
- Call Statistics 72
- RTP Statistics 75
- FAX Statistics 76
- SIP Settings 76
- Host aliases for SIP 77
- RTP Settings 77
- NAT Traversal Settings 78
- Line Settings 81
- Onboard Line Settings 81
- IP Line Settings 82
- Supporte 84
- IP Phones Templates 85
- Phones Logo 86
- FXS Gateway Management 87
- Loopback Settings 88
- Hot Desking 88
- FXO Settings 89
- Gain Control 95
- SIP Tunnel Settings 95
- • Failover Rea 100
- Local AAA Table 103
- Global Speed Dial Directory 104
- Allowed C 104
- Best Matching Algorithm 106
- VoIP Carrier Wizard 108
- RADIUS Client Settings 109
- Voice Mail Common Settings 111
- Dial Plan Settings 112
- 3PCC Settings 112
- RTP Streaming Channels 113
- Call Recording Settings 113
- Advanced PPP Settings 117
- VPN Configuration 117
- Dynamic DNS Settings 124
- Firewall and NAT 125
- Advanced Firewall Settings 125
- IP Pool 128
- IDS Log 130
- Network Menu 131
- DNS Settings 131
- DNS Server Settings 131
- Registration Form 134
- Voice Mail Profiles 135
- Administrator’s Logout 139
- Welcome 140
- Administrator Settings 141
- Extension Settings 147
- EPYGI TECHNOLOGIES, LTD 149
- Software License Agreement 149
Related products and manuals for Premise Branch Exchange (PBX) systems Quadro Quadro16xi
(2 pages)
(11 pages)© 2020, manymanuals.com. All rights reserved. | 1.756 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals