Quadro Quadro16xi Installation Guide Page 93
- Page / 150
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Quadro Manual II: Administrator's Guide Administrator’s Menus
Quadro2x, 2xi, Quadro4x, 4xi, Quadro16x, 16xi; (SW Version 5.2.x) 92
When the Alternative Disconnection Mode checkbox is not selected, Quad
received from the peer. When the checkbox is selected, Quadro’s user may
ro will disconnect the call as soon as the disconnect message has been
hear a busy tone when peer has been disconnected.
Th ckbox selection enables SIP P-Asserted-Identity support. For the calls from SIP to ISDN if Invite
SI Preferred-Identity or Remote-Party-ID, then the CallerID on ISDN is sent with the value from the
id en P-Preferred-Identity then Remote-Party-ID to fill the identity field.
W ing Party Subaddress checkbox is selected, Quadro will send the extension number as subaddress and the value defined in
th n this checkbox is disabled, no subaddress information will be sent and
th ng to the selection of the Use Default Outgoing Caller ID checkbox (see above). Caller ID information, along
wi e and PBX settings and capabilities.
Th for voice transfer. Disabling the timeslot will prevent both incoming and
outgoing calls.
Clicking on the ISDN Stats link will open the ISDN Status page that displays ISDN traffic statistics on the corresponding ISDN trunk. The ISDN
St where ISDN trunk and traffic statistics can be viewed.
down.
nal synchronization state in the
number of packets received in HDLC (High-
r shows the number of packets received with CRC
of received aborted packets.
Th
tra
rolling packets while the
e Override CLID with P-Asserted-Identity che
P message contains a P-Asserted-Identity or P-
entity field. SIP user agent should check existence of P-Asserted-Identity th
hen the Send Call
e Default outgoing Caller ID field as caller ID on the outgoing call. Whe
e caller ID will be defined accordi
th the Subaddress, can be displayed on the phone display depending on the phon
e B1 Channel and B2 Channel checkboxes enables/disables timeslots
ats link is displayed for every active trunk on the board and refers to the page
The ISDN Trunk Status page provides the following information about the
selected trunk state:
Link displays the ISDN link state: up or
Frame Synchronization displays the sig
trunk: Yes or No.
HDLC Receive shows the
level Data Link Control) format.
HDLC CRC Erro
(Cyclical Redundancy Check) errors.
HDLC Packet Abort displays the number
HDLC Transmit displays the number of packets transmitted in HDLC
format.
HDLC Octet Count displays the number of error packets received in
HDLC format.
e following SDN BRI Layer 2 statistics are displayed for received and
nsmitted packets:
TEI value shows the actual TEI value.
L2 State shows the actual BRI L2 state.
Information Frame shows the number of signaling packets for call
initiation and termination.
Receive Ready displays the number of cont
ISDN link is up.
Receive Not Ready displays the number of controlling packets in case
of inability to accept calls by destination.
SABME shows the number of packets upon connection establishment.
Fig. II-160: ISDN Trunk Status page
ement shows the number of packets upon accepting connection establishment/termination.
Identifier) to initiate subscription of the device in the network.
ckets received for call initiation and termination.
ith an incorrect supervisory header.
Bad Unnumbered Information Frame shows the number of packets with an incorrect unnumbered information frame header.
Bad Frame Type shows the number of packets with a bad frame type.
Disconnected Mode shows the number of packets when the connection is being disconnected.
Disconnect shows the number of packets upon connection termination.
Unnumbered Acknowledg
Framer shows the number of packets as a result of an error condition.
TEI Request shows the number of packets containing TEI (Terminal Endpoint
Unnumbered Information Frame shows the number of broadcast signaling pa
Exchange Identification shows the number of received packets containing connection management settings.
ISDN BRI Layer 2 Errors statistics:
Incorrect Length shows the number of packets with an incorrect length.
Bad Supervisory Frame shows the number of packets w
- Edition 1, June 2011 1
- Table of Contents 2
- Quadro’s Graphical Interface 6
- Recurrent Buttons 7
- Recurrent Functional Buttons 7
- Administrator’s Menus 8
- System Security Management 12
- • User Rights Management 13
- • IP Line Settings 13
- • Firewall/NAT 13
- Network Status 15
- Memory Status 19
- Hardware Status 20
- SIP Registration Status 20
- IP Lines Registration Status 20
- License Status 21
- IP Routing Configuration 21
- Configuration Management 23
- Time/Date Settings 28
- Mail Settings 29
- SMS Settings 30
- Firmware Update 30
- Automatic Firmware Update 32
- Networking Tools 33
- SNMP Settings 34
- Diagnostics 35
- System Logs 35
- Fig. II-64: Features page 37
- Upload Language Pack 38
- User Rights Management 39
- Users Menu 41
- Extensions Management 41
- User Extension Settings 43
- Call Park Extension Settings 49
- Attendant Extension Settings 55
- • PSTN – calls to PSTN 56
- • User Input 58
- • No input 58
- • Signs (“*” and “#”) 58
- Add Multiple Extensions 61
- Extension Codecs 62
- Call Park Service 63
- Recording Box 64
- Receptionist Management 65
- * key combination (see 67
- Authorized Phones Database 69
- Call Back Services 70
- Telephony Menu 72
- Call Statistics 72
- RTP Statistics 75
- FAX Statistics 76
- SIP Settings 76
- Host aliases for SIP 77
- RTP Settings 77
- NAT Traversal Settings 78
- Line Settings 81
- Onboard Line Settings 81
- IP Line Settings 82
- Supporte 84
- IP Phones Templates 85
- Phones Logo 86
- FXS Gateway Management 87
- Loopback Settings 88
- Hot Desking 88
- FXO Settings 89
- Gain Control 95
- SIP Tunnel Settings 95
- • Failover Rea 100
- Local AAA Table 103
- Global Speed Dial Directory 104
- Allowed C 104
- Best Matching Algorithm 106
- VoIP Carrier Wizard 108
- RADIUS Client Settings 109
- Voice Mail Common Settings 111
- Dial Plan Settings 112
- 3PCC Settings 112
- RTP Streaming Channels 113
- Call Recording Settings 113
- Advanced PPP Settings 117
- VPN Configuration 117
- Dynamic DNS Settings 124
- Firewall and NAT 125
- Advanced Firewall Settings 125
- IP Pool 128
- IDS Log 130
- Network Menu 131
- DNS Settings 131
- DNS Server Settings 131
- Registration Form 134
- Voice Mail Profiles 135
- Administrator’s Logout 139
- Welcome 140
- Administrator Settings 141
- Extension Settings 147
- EPYGI TECHNOLOGIES, LTD 149
- Software License Agreement 149
Related products and manuals for Premise Branch Exchange (PBX) systems Quadro Quadro16xi
(2 pages)
(11 pages)© 2020, manymanuals.com. All rights reserved. | 0.476 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals