Quadro Quadro16xi Installation Guide download pdf (Page 7)

Quadro Manual II: Administrator's Guide Appendix: PBX Services for Quadro’s Administrator

Quadro2x, 2xi, Quadro4x, 4xi, Quadro16x, 16xi; (SW Version 5.2.x) 6

Recurrent Buttons

Throughout this guide, you will see a variety of recurrent buttons. Below is a description of these buttons.

Button Description Button Description

This button leads back to the previous

page of a fixed sequence of pages (used

mainly in wizards).

This button returns you to the page you were

previously on.

This button leads forward to the next page

of a fixed sequence of pages (used mainly

in wizards).

This button confirms an operation you started

before.

This button discards the latest not yet

confirmed entries.

This button confirms an operation you chose

before.

This is the last button of a fixed sequence

of pages that completes and saves the

entries of an entire sequence.

This button discards an operation you chose

before.

This button opens the help page

belonging to the currently active Quadro

management page.

This button saves the settings modified on the

currently active management page.

This button opens a window where the last

inserted IP addresses are listed. It allows

the user to make a quick selection of an IP

address that has been previously used.

This will avoid the user needing type it

again. The clipboard can hold up to 10 IP

addresses and a new IP address will

replace the oldest one from the list.

This button opens a window where the last

inserted SIP addresses are listed. It allows the

user to make a quick selection of an IP address

that has been previously used. This will avoid

the user needing type it again. The clipboard

can hold up to 10 SIP addresses and a new

SIP address will replace the oldest one from the

list.

Recurrent Functional Buttons

In connection with the tables, the following are the few buttons you will see:

Functional Button Description

Add Allows adding a new record to the displayed table. A new page will be displayed to enter any new settings.

Edit

Allows modifying the settings of the record selected by a checkbox. Normally only one (1) record may be selected. A new

page will be displayed to enter the modified settings.

Delete Deletes the selected entry(s) of a table. A warning message will ask for confirmation before deleting an existing entry.

Select All Selects all table entry(s) for example for further deletion.

Inverse Selection

Inverses (opposites) an existing selection of table entry(s). If no entries are selected, clicking the button will select all

records.

Refresh in...

May be shown in the upper right corner of a page. It displays the number of seconds remaining until the next refresh of the

page will occur. It may be used to reload the page manually.

Most of the tables offer the option to sort the entries in ascending or descending order by clicking the headings of the columns. A small arrow next to

the column heading indicates the direction of sorting - upward or downward. The entries of the table can be selected by using the corresponding

checkboxes in order to edit or delete them.

Entering SIP Addresses Correctly

Calls over IP are implemented based on Session Initiating Protocol (SIP) on the Quadro. When making a call to a destination that is somewhere on

the Internet, a SIP address must be provided.

SIP addresses needs to be specified in one of the following formats:

“display name” <username@ipaddress:port>

“display name” <username@ipaddress>

username@ipaddress:port

username@ipaddress

username

The display name and the port number are optional parameters in the

SIP address. If a port is not specified, 5060 will be set up as the default

one. The range of valid ports is between 1024 and 65536.

A flexible structure of wildcards is allowed. In comparison with a

wildcard, the “?” character stands for only one unknown digit and the “*”

character stands for any number of any digits.

For your convenience, the following combinations can be used:

• *@ipaddress - any user from the specified SIP server

• username@* - a specified user from any SIP server

• *@* - any user from any SIP server

Please Note: Wildcards are available for caller addresses only. No

wildcard characters are allowed for called party addresses. Exceptions

are addresses in the Supplementary Addresses table that are used by

Outgoing Call Blocking and Hiding Caller Information Settings

services. To use “*” and “?” alone (as non wildcard characters), use “\*”

and “\?” correspondingly.

1 2 3 4 5 6 7 8 9 10 11 12 ... 149 150

Comments to this Manuals

No comments

Quadro Quadro16xi Installation Guide Page 7

Comments to this Manuals

Related products and manuals for Premise Branch Exchange (PBX) systems Quadro Quadro16xi