Quadro Quadro16xi Installation Guide download pdf (Page 88)

Quadro Manual II: Administrator's Guide Administrator’s Menus

Quadro2x, 2xi, Quadro4x, 4xi, Quadro16x, 16xi; (SW Version 5.2.x) 87

assign the provided FXS lines to the first available IP lines on the

there are no enough free IP lines

Quadro IP PBX. You may adjust the configuration from this page.

Please Note: The FXS lines can be assigned only to inactive IP

nes on the Quadro IP PBX. If li

available on the Quadro IP PBX, you should first deactivate the IP

line from the IP Line Settings

page to use it in the FXS Gateway

Configuration Wizard.

The next page of the wizard is FXS Gateway Configuration

Wizard - Summary where the configured settings should be

erified. v

Once FXS Gatew

is added to the table and th

ay Configuration Wizard terminates, a new entry

e corresponding FXS Gateway's

configuration gets updated according to the settings defined in the

wizard, i.e. corresponding routing rules will be added to the Call

Routing table of the FXS Gateway. If you need to reboot the FXS

gateway, use the Reboot functional button in the FXS Gateway

Management page.

k Settings page is used to configure the lines for voice loopback diagnostics. When loopback is enabled on the line, any

coming calls to the corresponding line will automatically pick up on the first ring and any voice towards the line will automatically be sent back to the

themselves in the handset). Loopback Timeout provides the option of limiting the voice loopback diagnostics duration, i.e.

connected from the Quadro when the Loopback Timeout expires.

back diagnostics

oopback service on the selected FXS line(s).

Fig. II-151: FXS Gateway Management Wizard – page 2

Loopback Settings

The FXS Lines Loopbac

caller (the caller will hear

the caller will be dis

The FXS Lines Loopback Settings page shows the only table where all FXS lines of the Quadro are listed. On this page, the loop

may be enabled/disabled and the Loopback Timeout can be adjusted for FXS lines.

The FXS Lines Loopback table lists all the FXS lines on the

Quadro along with their loopback parameters (Loopback State

and Loopback Timeout).

The Edit functional link leads to the FXS Lines Loopback

Settings - Edit Entry page where Loopback Timeout (in

seconds) may be configured for one or more selected FXS line(s).

The Enable/Disable Loopback functional link is used to

enable/disable the L

Fig. II-152: IP Line Settings –Loopback page

nes connected and much more users wishing to make and receive calls through the Quadro,

ones have no static owners; they are just connected to the analogue or IP

the previously created virtual extension and the corresponding password in

point forward and unless the user with log off the phone, he may place and

e public phones. Each user should have a virtual extension configured in the

Hot Desking

If Quadro has limited number of analogue and IP pho

some of the connected phones can be announced as public. Public ph

lines. Each user that accesses the public phone should first login with

order to make the phone assigned to the certain extension. From that

receive calls and use all the supplementary PBX services of the Quadro.

The Hot Desking feature is used to organize the user login/logout on th

Extensions Management

table. The virtual extensions can be configure

user will log in from the phone with that extension. The Hot Deski

d as needed to use all the available supplementary PBX features when the

ng option should be enabled on the corresponding analogue or IP lines from the

Line SettingsIP

page accordingly.

s chapter). You will be prompted for the extension and the

place

se Voice Mail services, etc. When you have finished using

comes again virtual and is not connected to any analogue

t Grouping, etc. services) and voice mails according to the

supp e more assigned to your extension and is now available for other

users to login and use it.

To login to the phone, use the *78 feature code (for more details see Feature Code

password. When you login to the phone with your extension, the phone becomes a fully featured phone connected to the Quadro. You may

and received calls with the SIP address configured in the Extensions Management page, u

the phone, logout with the *78 feature code. From that moment forward, your extension be

or IP line but it still can handle calls (using Call Forwarding, Many Extension Ringing, Hun

lem ntary service configured on that virtual extension. The phone becomes no

1 2 ... 83 84 85 86 87 88 89 90 91 92 93 ... 149 150

Comments to this Manuals

No comments

Quadro Quadro16xi Installation Guide Page 88

Comments to this Manuals

Related products and manuals for Premise Branch Exchange (PBX) systems Quadro Quadro16xi