Quadro Quadro16xi Installation Guide download pdf (Page 89)

Quadro Manual II: Administrator's Guide Administrator’s Menus

Quadro2x, 2xi, Quadro4x, 4xi, Quadro16x, 16xi; (SW Version 5.2.x) 88

FXO Settings

The FXO Settings are used to configure the FXO support that allows Quadro to connect to other PBXs or analog telephone lines.

o. Quadro2x has only one FXO port available. Quadro4x has two FXO

XO ports available.

oing calls for the selected FXO line if required. Depending on the Quadro

ou the option connect several PSTN lines to the Quadro and to use them

T e e calls from the Central Office (PSTN) will be routed.

The assig

Quadro A

from the

desired e

The FXO al FXO lines, shared

n disabled, the Allowed Call Type, Route Incoming

The number of available FXO ports is dependent on the type of your Quadr

ports available. Quadro16x and the special edition of Quadro4x have 4 F

The FXO Settings also gives you the option to limit incoming or outg

model, several FXO ports will be available on the board, thus giving y

simultaneously.

h a ministrator may assid gn a default recipient for each FXO line wher

ned recipients become the Quadro “default users”. If the

uto Attendant has been selected as a “default user”, a caller

PSTN needs to go through the attendant menu to reach the

xtension.

Settings page lists the available loc

FXO lines on the remote devices (if any) and their settings. If the FXO

service has bee

Call to and PSTN number columns are set to “N/A”.

Clicking on the FXO line number will open the FXO Settings - FXO#

page where the FXO line settings may be modified. If having External

PSTN Gateways

service is enabled and the local Quadro provides its

FXO lines to the remote device, no FXO lines’ settings can be

modified on the local Quadro. In this case, all shared FXO lines can

nly be configured from the remote device. Any modifications in the

the master Quadro will immediately be

ble on the slave Quadro.

shared FXO line’s settings on

reflected in the FXO Settings ta

Fig. II-153: FXO Settings page

The call directions for the corresponding FXO line. The administrator may choose between:

line.

• Enabling both incoming and outgoing calls for the selected FXO line.

g FXO Call to manipulation radio buttons group

the destination where incoming calls addressed

calls to the destination defined through Call Routing

The Enable FXO checkbox selection activates FXO support for the selected FXO line.

Allowed Call Type is used to choose the allowed

• Enabling incoming calls (prohibiting outgoing calls) for the selected FXO

oming calls) for the selected FXO line. • Enabling outgoing calls (prohibiting inc

The Route incomin

allows you to define

to the corresponding FXO line will be forwarded to.

• Extension – this selection allows you to choose the local

PBX user or auto attendant extension to forward calls. If an

inactive extension is chosen from this list, the voice mail

system will answer the call addressed to the corresponding

FXO line. If the Auto Attendant extension is chosen, it will

become the “default user” for the corresponding FXO line

on the Quadro.

• Routing – this selection allows you to forward the incoming

. This

selection requires you to enter a routing pattern to the

corresponding field. Based on the registered PSTN users,

the caller will be able to reach the destination according to

configurations in Call Routing Table.

Fig. II-154: FXO Line Settings page

By choosing a destination, the Quadro administrator virtually assigns a default number that will start ringing when a call is initiated to the Quadro’s

is optional and used as

ermany, Israel, France, etc.) selected for Quadro has two COs that use different

ur AC termination mode. Selecting the checkbox may help if the voice quality over FXO is

PSTN number.

The PSTN Number text field allows you to enter the PSTN number that the current FXO line is attached to. The field value

an identification parameter for FXO lines. The field value can be left empt

Alternative AC Termination Mode appears if the local country (G

types of AC termination. Contact your CO to learn about yo

poor or an echo is noticed.

To modify the FXO Settings

1. Select the FXO line number from the FXO Settings table. Th

2. Enable the FXO line to receive calls from the PSTN. To reject

3. If FXO has been enabled, select the Call Type from the Allow

down list to route

e FXO Settings -FXO# will appear where the line settings may be modified.

calls from/to the PSTN, deselect the Enable FXO checkbox.

ed Call Type drop down list and the extension from the Route FXO Call to drop

the FXO calls correspondingly.

the FXO line.

a requirement of your CO.

Press Save to submit the FXO line settings.

4. Insert a PSTN number in the same named text field to identify

5. Enable Alternative AC Termination Mode if this is

1 2 ... 84 85 86 87 88 89 90 91 92 93 94 ... 149 150

Comments to this Manuals

No comments

Quadro Quadro16xi Installation Guide Page 89

Comments to this Manuals

Related products and manuals for Premise Branch Exchange (PBX) systems Quadro Quadro16xi