Quadro Quadro16xi Installation Guide Page 10
- Page / 150
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Quadro Manual II: Administrator's Guide Administrator’s Menus
Quadro2x, 2xi, Quadro4x, 4xi, Quadro16x, 16xi; (SW Version 5.2.x) 9
Internet Configuration Wizard
The Internet Configuration Wizard allows the administrator to configure the WAN interface settings and to adjust Quadro’s connectivity with an
external network. The Internet Configuration Wizard MUST be run for Quadro to be connected to the Internet.
All the settings of the Internet Configuration Wizard are
described in the chapters below except those for the IP settings,
which will be described in this chapter.
Please Note: It is strongly recommended not to change the
factory default settings if their meanings are not fully clear
to an administrator.
Fig. II-7: Internet Configuration Wizard - Start page
The Wizard allows navigating through the following basic configuration parameters and settings:
• Uplink configuration (see below)
For WAN Interface protocol PPPoE:
• PPP/ PPTP Settings
• WAN Interface Configuration (see below)
• DNS Settings
For WAN Interface protocol PPTP:
• WAN IP Configuration (see below)
• PPP/ PPTP Settings
• WAN Interface Configuration (see below)
• DNS Settings
For WAN Interface protocol Ethernet:
• WAN IP Configuration
• WAN Interface Configuration (see below)
• DNS Settings
•
The Switch to Auto Provisioning link moves you to the Automatic Provisioning
page where Quadro can be configured automatically.
The Uplink Configuration page allows you to select the Quadro‘s
WAN interface connection type and its bandwidth settings. These
settings will make Quadro available to the external network.
Depending on the Uplink Interface Protocol selection, the page
following the Uplink Configuration page is different. Thus if
PPPoE is selected, the next page will be PPP Configuration, while
selecting Ethernet will bring up the WAN IP Configuration page.
The Uplink Configuration page offers the following components:
The WAN Interface Protocol radio buttons are used to choose the
protocol depending on the requirements of the ISP (Internet Service
Provider):
PPPoE - turns on the PPP over an Ethernet connection.
PPTP – turns on the Point to Point Tunneling Protocol (PPTP)
interface used for the connection between Quadro and ADSL
modem. A fixed IP address configuration is needed in this
case.
Ethernet - turns on the Ethernet connection.
Fig. II-8: Internet Configuration Wizard - Uplink Configuration page
The WAN Interface Bandwidth settings allow the specification of the upstream and downstream speeds in kbit/s, helping to assure the quality of IP
calls. An IP call looses the voice quality if there is no available bandwidth. When approaching the limits of bandwidth capacity, another IP call will be
declined.
The bandwidth provided by the ISP has to be specified in the text fields Upstream Speed and Downstream Speed. The default entry in both fields
is 10000, the maximum bandwidth of a 10 MB Ethernet. In most cases, providers offer a smaller bandwidth than 10000 kbit/s. You may see the
required bandwidth in the chapter Needed Bandwidth for IP Calls
.
- Edition 1, June 2011 1
- Table of Contents 2
- Quadro’s Graphical Interface 6
- Recurrent Buttons 7
- Recurrent Functional Buttons 7
- Administrator’s Menus 8
- System Security Management 12
- • User Rights Management 13
- • IP Line Settings 13
- • Firewall/NAT 13
- Network Status 15
- Memory Status 19
- Hardware Status 20
- SIP Registration Status 20
- IP Lines Registration Status 20
- License Status 21
- IP Routing Configuration 21
- Configuration Management 23
- Time/Date Settings 28
- Mail Settings 29
- SMS Settings 30
- Firmware Update 30
- Automatic Firmware Update 32
- Networking Tools 33
- SNMP Settings 34
- Diagnostics 35
- System Logs 35
- Fig. II-64: Features page 37
- Upload Language Pack 38
- User Rights Management 39
- Users Menu 41
- Extensions Management 41
- User Extension Settings 43
- Call Park Extension Settings 49
- Attendant Extension Settings 55
- • PSTN – calls to PSTN 56
- • User Input 58
- • No input 58
- • Signs (“*” and “#”) 58
- Add Multiple Extensions 61
- Extension Codecs 62
- Call Park Service 63
- Recording Box 64
- Receptionist Management 65
- * key combination (see 67
- Authorized Phones Database 69
- Call Back Services 70
- Telephony Menu 72
- Call Statistics 72
- RTP Statistics 75
- FAX Statistics 76
- SIP Settings 76
- Host aliases for SIP 77
- RTP Settings 77
- NAT Traversal Settings 78
- Line Settings 81
- Onboard Line Settings 81
- IP Line Settings 82
- Supporte 84
- IP Phones Templates 85
- Phones Logo 86
- FXS Gateway Management 87
- Loopback Settings 88
- Hot Desking 88
- FXO Settings 89
- Gain Control 95
- SIP Tunnel Settings 95
- • Failover Rea 100
- Local AAA Table 103
- Global Speed Dial Directory 104
- Allowed C 104
- Best Matching Algorithm 106
- VoIP Carrier Wizard 108
- RADIUS Client Settings 109
- Voice Mail Common Settings 111
- Dial Plan Settings 112
- 3PCC Settings 112
- RTP Streaming Channels 113
- Call Recording Settings 113
- Advanced PPP Settings 117
- VPN Configuration 117
- Dynamic DNS Settings 124
- Firewall and NAT 125
- Advanced Firewall Settings 125
- IP Pool 128
- IDS Log 130
- Network Menu 131
- DNS Settings 131
- DNS Server Settings 131
- Registration Form 134
- Voice Mail Profiles 135
- Administrator’s Logout 139
- Welcome 140
- Administrator Settings 141
- Extension Settings 147
- EPYGI TECHNOLOGIES, LTD 149
- Software License Agreement 149
Related products and manuals for Premise Branch Exchange (PBX) systems Quadro Quadro16xi
(2 pages)
(11 pages)© 2020, manymanuals.com. All rights reserved. | 0.591 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals