Quadro Manual II: Administrator's Guide Administrator’s Menus
Quadro2x, 2xi, Quadro4x, 4xi, Quadro16x, 16xi; (SW Version 5.2.x) 50
The Address text field is used to define the address to be included in the Retrieve Access List table. The value in this field is strictly dependent on
the Call Type defined in the same named drop down list. If the PBX call type is selected, the Quadro extension number should be defined in this
field. For the SIP call type, the SIP address should be defined, for the PSTN call type, the PSTN user number should be defined here. The wildcard
is supported in this field.
Paging Group Extension Settings
Paging Group & Access List
The Paging Group service is used to page a group of extensions by forcing extensions to go off-hook and opening one-way communication. The
service is particularly used for announcements addressed to a group of extensions. Service allows to page multiple extensions by dialing the Paging
Group extension.
Please Note: The Paging Group service requires called extensions to use one of the following SIP or analog phones which are able to
automatically go off-hook:
• snom 190
• snom 200
• snom 220
• snom 300
• snom 320
• snom 360
• snom 370
• snom 820
• snom 870
• SNOM MeetingPoint
• Aastra 480i
• Aastra 480iCT
• Aastra 9112i
• Aastra 9133i
• Aastra 9143i(33i)
• Aastra 9480i(35i)
• Aastra 9480iCT
• Aastra 6751i
• Aastra 6753i
• Aastra 6755i
• Aastra 6757i
• Aastra 6757iCT
• Aastra 6730i
• Aastra 6731i
• Aastra 480e (analog phone)
• Grandstream BT200
• Grandstream GXP2000
• Polycom SoundPoint IP 300SIP
• Polycom SoundPoint IP 330SIP
• Polycom SoundPoint IP 331SIP
• Polycom SoundPoint IP 335SIP
• Polycom SoundPoint IP 450SIP
• Polycom SoundPoint IP 501SIP
• Polycom SoundPoint IP 550SIP
• Polycom SoundPoint IP 601SIP
• Polycom SoundPoint IP 650SIP
• Polycom SoundStation IP 6000
• Polycom VVX 1500
• Linksys SPA921
• Linksys SPA922
• Linksys SPA941
• Linksys SPA942
• Yealink T20
• Yealink T22
• Yealink T26
• Yealink T28
The Paging Group list is used to define the extensions that will be paged. They will automatically go off-hook when the paging call comes in.
The Access List is used to define PBX, SIP or PSTN users that are explicitly allowed/forbidden to activate the call paging using the corresponding
extension.
When calling to the Paging Group extension, the call will be forwarded to the extensions listed in the Paging Group table. The phones of the called
extensions will automatically go off-hook (the phone speaker automatically becomes activated) and the caller will be able to make his announcement.
Since the paging call opens one-way communication, the called extensions will not be able to give an answer to the caller. To terminate the paging
call, caller should simply hang up.
Attention: Call paging will not work if the called extension is in call.
When caller not listed in the Access List calls the Paging Group extension, password authorization (using the password of the Paging Group
extension) will be required to start the call paging. When a denied user tries to call the Paging Group extension, “Party does not accept your call”
message will be played to the caller. When caller dials the Paging Group extension with empty Paging Group table, “Number dialed temporarily
unavailable” message will be played to the caller.
For Paging Group extensions, Extensions Management - Edit Entry page consists of General Settings, SIP Settings and Advanced SIP
Settings pages. The SIP Settings and Advanced SIP Settings pages are the same as for the regular extensions (see User Extension Setting
s),
while General Settings page has a different content:
Comments to this Manuals