Quadro Quadro16xi Installation Guide Page 92
- Page / 150
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Quadro Manual II: Administrator's Guide Administrator’s Menus
Quadro2x, 2xi, Quadro4x, 4xi, Quadro16x, 16xi; (SW Version 5.2.x) 91
• Idle Timer T203 configures the period in milliseconds (numeric values from 1000 to 99999) for the ISDN client idle timeout.
ISDN L3 Timers:
• The T302 Timer text field requires the value for the T302
timer in milliseconds (digit values from 0 to 15000). It
indicates that the time frame system is waiting for a digit to
be dialed. When the timer expires, it initiates the call.
• T309 Timer requires the value for the T309 timer in
milliseconds (numeric values from 0 to 90000). It is
responsible for call steadiness during link disconnection
within the period equal to this timer value. If the value in
It is
n CALL
PR
call confirmation (ALERT, CONNECT, DISC or
s connected to a slow ISDN-
ISDN-PBX (350ms);
this field is zero (0), the T309 timer will be disabled.
• T310 Timer requires the value for the T310 timer in
milliseconds (numeric values from 1000 to 120000).
responsible for the outgoing call steadiness whe
dy received from the destination but OCEEDING is alrea
PROGRESS) has not yet arrived.
• Alert Guard Timeout requires the value for the Alert
Guard Timer in milliseconds (numeric values from 0 to 500)
between CALL PROC and ALERT messages. Alert Guard
Timer it is used when Quadro i
PBX.
Recommended values are:
• - fast connection (0ms);
- normal (150ms), default;
- slow
• - very slow ISDN-PBX (500ms).
Fig. II-159: ISDN Wizard – l2&L3 Settings
trunk will lose the
if
only by the timeslot asked
the call request.
• on call acceptance
The Calling Party Type of Number drop down list allows you to select the type identifying the origin of call.
The Called Party Type of Number drop down list allows you to select the type identifying the subaddress of the called party of the call.
The Called Party Numbering Plan and Calling Party Numbering Plan drop down lists correspondingly indicate the numbering plan of the called
party's and calling party's number.
The Incoming Called Digits Size text field indicates the number of received digits (in a range from 0 to 255) required to establish a call. When this
field has a “0” value, the system uses either the timeout defined in the T302 field or the Sending Complete Information element messages to
establish a call. Independent on the value in this field, Sending Complete Information element and the pound sign always result in call
establishment.
The Generate Progress tone on IP checkbox selection will generate the progress tone to IP.
When Generate Progress Tone to PSTN/PBX checkbox is selected, Quadro generates ring tones to callers during ISDN call dialing. This feature is
mainly applicable to 2-stage dialing mode.
Enable CLIR Service checkbox selection enables Calling Line Identification Restriction (CLIR) service which displays the incoming caller ID only if
Presentation Indication is allowed on the remote side. Otherwise, if CLIR service is disabled, caller ID will be unconditionally displayed.
The Coding Type drop down list allows you to select between a-law and mu-law coding types.
The Switch Type is another configuration parameter that depends on the Service Provider.
The Passive Mode checkbox is used to leave the ISDN Layer1 connection in the Slave mode. When this checkbox is selected, Layer1 remains idle
when calls are not available. When this checkbox is not selected, Quadro keeps its Layer1 always active. This checkbox enables the Enable TEI
Remove Procedure and Permanent TEI Value checkboxes. With the Enable TEI Remove Procedure checkbox is selected, the
assigned TEI when entering into passive mode on the Layer 2. With the Permanent TEI Value checkbox is selected, the trunk will keep the assigned
TEI when entering into passive mode on the Layer 2 or when Quadro detected ISDN link DOWN signal from carrier.
These checkboxes are present only for connection types different from PTP (Point to Point) selected on the first page of ISDN Wizard. In case
PTP (Point to Point) connection type is selected on the first page of the ISDN Wizard, these two checkboxes are replaced with a TEI Address text
field that requires the channel number (digit values from 0 to 63) for connection establishment between the CO and the ISDN client.
Channel Selection is used to select between the Preferred and Exclusive B channel selection methods. For Preferred channel selection, the CO
answers to the call request by the first available timeslot. With the Exclusive channel selection, the CO should feedback
in
The Bearer Establishment Procedure drop down list allows selecting the session initiation method on the B channel. One of the following options
can be selected for the transmission path completion prior to receipt of a call acceptance indication:
• on channel negotiation at the destination interface
• on progress indication with in-band information
- Edition 1, June 2011 1
- Table of Contents 2
- Quadro’s Graphical Interface 6
- Recurrent Buttons 7
- Recurrent Functional Buttons 7
- Administrator’s Menus 8
- System Security Management 12
- • User Rights Management 13
- • IP Line Settings 13
- • Firewall/NAT 13
- Network Status 15
- Memory Status 19
- Hardware Status 20
- SIP Registration Status 20
- IP Lines Registration Status 20
- License Status 21
- IP Routing Configuration 21
- Configuration Management 23
- Time/Date Settings 28
- Mail Settings 29
- SMS Settings 30
- Firmware Update 30
- Automatic Firmware Update 32
- Networking Tools 33
- SNMP Settings 34
- Diagnostics 35
- System Logs 35
- Fig. II-64: Features page 37
- Upload Language Pack 38
- User Rights Management 39
- Users Menu 41
- Extensions Management 41
- User Extension Settings 43
- Call Park Extension Settings 49
- Attendant Extension Settings 55
- • PSTN – calls to PSTN 56
- • User Input 58
- • No input 58
- • Signs (“*” and “#”) 58
- Add Multiple Extensions 61
- Extension Codecs 62
- Call Park Service 63
- Recording Box 64
- Receptionist Management 65
- * key combination (see 67
- Authorized Phones Database 69
- Call Back Services 70
- Telephony Menu 72
- Call Statistics 72
- RTP Statistics 75
- FAX Statistics 76
- SIP Settings 76
- Host aliases for SIP 77
- RTP Settings 77
- NAT Traversal Settings 78
- Line Settings 81
- Onboard Line Settings 81
- IP Line Settings 82
- Supporte 84
- IP Phones Templates 85
- Phones Logo 86
- FXS Gateway Management 87
- Loopback Settings 88
- Hot Desking 88
- FXO Settings 89
- Gain Control 95
- SIP Tunnel Settings 95
- • Failover Rea 100
- Local AAA Table 103
- Global Speed Dial Directory 104
- Allowed C 104
- Best Matching Algorithm 106
- VoIP Carrier Wizard 108
- RADIUS Client Settings 109
- Voice Mail Common Settings 111
- Dial Plan Settings 112
- 3PCC Settings 112
- RTP Streaming Channels 113
- Call Recording Settings 113
- Advanced PPP Settings 117
- VPN Configuration 117
- Dynamic DNS Settings 124
- Firewall and NAT 125
- Advanced Firewall Settings 125
- IP Pool 128
- IDS Log 130
- Network Menu 131
- DNS Settings 131
- DNS Server Settings 131
- Registration Form 134
- Voice Mail Profiles 135
- Administrator’s Logout 139
- Welcome 140
- Administrator Settings 141
- Extension Settings 147
- EPYGI TECHNOLOGIES, LTD 149
- Software License Agreement 149
Related products and manuals for Premise Branch Exchange (PBX) systems Quadro Quadro16xi
(2 pages)
(11 pages)© 2020, manymanuals.com. All rights reserved. | 2.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals