Quadro Quadro16xi Installation Guide Page 45
- Page / 150
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Quadro Manual II: Administrator's Guide Administrator’s Menus
Quadro2x, 2xi, Quadro4x, 4xi, Quadro16x, 16xi; (SW Version 5.2.x) 44
Authentication User Name requires an identification parameter
to reach the SIP server. It should be provided by the SIP service
provider and can be requested for some SIP servers only. For
others, the field should be left empty.
Send Keep-alive Messages to Proxy enables the SIP
registration server accessibility to the verification mechanism.
Timeout indicates the timeout between two attempts for the SIP
registration server accessibility verification. If no reply is received
from the primary SIP server within this timeout, the Secondary SIP
server will be contacted. When the primary SIP server recovers,
SIP packets will resume being sent to it.
The RTP Priority Level drop down list is used to select the priority
(low, medium or high) of the RTP packets sent from a
corresponding extension. RTP packets with higher priority will be
sent first in case of heavy traffic.
The Do Not Use SIP Old Hold Method checkbox enables the
new recommended method of call hold in SIP, in which case the
hold request is indicated with the "a=sendonly" media attribute,
rather than with the IP address of 0.0.0.0 used before. The
checkbox should be enabled if the remote party does not
recognize hold requests initiated from the Quadro.
A group of Host address and Port text fields respectively require
the host address (IP address or the host name) and the port
numbers of the Outbound Proxy, Secondary SIP Server and the
Outbound Proxy for the Secondary SIP Server. These settings
are provided by the SIP servers’ providers and are used by
Quadro to reach the selected SIP servers.
Fig. II-79: Extensions Management - Edit Entry – Advanced SIP Settings page
4. Remote Settings
This group is used to configure SIP Remote Extension functionality. This is an advanced telephony feature that allows Quadro users to remotely
operate Quadro. Users need to register a hardware or software SIP phone on the Quadro by defining the Quadro’s global IP address and an
appropriate Username/Password. A registered SIP Remote phone can act fully as a phone connected locally to Quadro, i.e. it can use Quadro’s PBX
features, place and receive calls, access voice mails, etc.
The Enable checkbox activates the SIP Remote Extension’s functionality.
Please Note: SIP Remote Extension functionality may be enabled only for active (attached to an onboard FXS or IP line) extensions.
Identification parameters used by the remote SIP device for registration on the Quadro should be defined in the Username and Password text
fields. They should match on both Quadro and SIP phone for a successful connection. The Password field is checked against its strength and you
may see how strong is your inserted password is right below that field. To achieve the well protected strong password minimum 8 characters of
letters in upper and lower case, symbols and numbers should be used. If you are unable to define a strong password, press Choose Generated
Password to use one of system defined strong passwords.
Line Appearance text field requires a number of simultaneous
calls supported by the SIP phone.
When the Enable RTP Proxy checkbox is selected, incoming and
outgoing RTP streams to and from the remote SIP phone will be
routed through Quadro. When the checkbox is not selected, RTP
packets will be moving directly between peers.
When the Fallback To Local Extension When Not Registered
checkbox is selected, incoming calls towards the corresponding
extension on the Quadro will be forwarded to the remote SIP
phone only if it is registered. Otherwise, when the remote SIP
phone is unregistered, incoming calls will be routed to the line
extension it is attached to. When this checkbox is not selected, all
incoming calls will be routed to the remote SIP phone only if it is
registered. Otherwise, if the remote SIP phone is unregistered,
calls will be forwarded to the extension’s voice mailbox.
The Symmetric RTP checkbox should be selected when the
remote extension is located behind the symmetrical NAT.
Fig. II-80: Extensions Management - Edit Entry – Remote Settings page
The Show Hot Desking Settings and Hide Hot Desking Settings links are correspondingly used to show or hide the Hot Desking settings on this
page.
The Enable Hot Desking Capability checkbox is used to enable the Hot Desking
feature on the corresponding remote extension.
- Edition 1, June 2011 1
- Table of Contents 2
- Quadro’s Graphical Interface 6
- Recurrent Buttons 7
- Recurrent Functional Buttons 7
- Administrator’s Menus 8
- System Security Management 12
- • User Rights Management 13
- • IP Line Settings 13
- • Firewall/NAT 13
- Network Status 15
- Memory Status 19
- Hardware Status 20
- SIP Registration Status 20
- IP Lines Registration Status 20
- License Status 21
- IP Routing Configuration 21
- Configuration Management 23
- Time/Date Settings 28
- Mail Settings 29
- SMS Settings 30
- Firmware Update 30
- Automatic Firmware Update 32
- Networking Tools 33
- SNMP Settings 34
- Diagnostics 35
- System Logs 35
- Fig. II-64: Features page 37
- Upload Language Pack 38
- User Rights Management 39
- Users Menu 41
- Extensions Management 41
- User Extension Settings 43
- Call Park Extension Settings 49
- Attendant Extension Settings 55
- • PSTN – calls to PSTN 56
- • User Input 58
- • No input 58
- • Signs (“*” and “#”) 58
- Add Multiple Extensions 61
- Extension Codecs 62
- Call Park Service 63
- Recording Box 64
- Receptionist Management 65
- * key combination (see 67
- Authorized Phones Database 69
- Call Back Services 70
- Telephony Menu 72
- Call Statistics 72
- RTP Statistics 75
- FAX Statistics 76
- SIP Settings 76
- Host aliases for SIP 77
- RTP Settings 77
- NAT Traversal Settings 78
- Line Settings 81
- Onboard Line Settings 81
- IP Line Settings 82
- Supporte 84
- IP Phones Templates 85
- Phones Logo 86
- FXS Gateway Management 87
- Loopback Settings 88
- Hot Desking 88
- FXO Settings 89
- Gain Control 95
- SIP Tunnel Settings 95
- • Failover Rea 100
- Local AAA Table 103
- Global Speed Dial Directory 104
- Allowed C 104
- Best Matching Algorithm 106
- VoIP Carrier Wizard 108
- RADIUS Client Settings 109
- Voice Mail Common Settings 111
- Dial Plan Settings 112
- 3PCC Settings 112
- RTP Streaming Channels 113
- Call Recording Settings 113
- Advanced PPP Settings 117
- VPN Configuration 117
- Dynamic DNS Settings 124
- Firewall and NAT 125
- Advanced Firewall Settings 125
- IP Pool 128
- IDS Log 130
- Network Menu 131
- DNS Settings 131
- DNS Server Settings 131
- Registration Form 134
- Voice Mail Profiles 135
- Administrator’s Logout 139
- Welcome 140
- Administrator Settings 141
- Extension Settings 147
- EPYGI TECHNOLOGIES, LTD 149
- Software License Agreement 149
Related products and manuals for Premise Branch Exchange (PBX) systems Quadro Quadro16xi
(2 pages)
(11 pages)© 2020, manymanuals.com. All rights reserved. | 0.973 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals